PP

Tugas Jarkom 3 Praktek

Planning and Building an Enterprise Network

Objective

·         Plan, design, and build a large enterprise network utilizing multiple VLANs, inter-VLAN routing, and VTP domains.

Background / Preparation

A new remote site has been acquired by your company and the network needs to be built. You must plan, design, and build the network to meet company standards. The following equipment has been provided.

·         Three Cisco 2960 switches have been purchased, one for each of the three floors.

·         One Cisco 1841 router has been purchased as the Integrated Service Router (ISR).

Step 1: Connecting the network

Utilize the first FastEthernet interface on the ISR router to connect to the last FastEthernet interface on the Floor 1 switch.

Connect GigabitEthernet 1/1 on the Floor 1 switch to GigabitEthernet 1/1 on the Floor 2 switch.

Connect GigabitEthernet 1/2 on the Floor 2 switch to GigabitEthernet 1/1 on the Floor 3 switch.

Step 2: Configure basic switch and router configurations

Utilize the following table to configure the ISR router, Floor 1, Floor 2, and Floor 3 switches.

Router

Router>en

Router>enable

Router#conf

Router#configure t

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#hos

Router(config)#hostname ISR_Rtr

ISR_Rtr(config)#en

ISR_Rtr(config)#ena

ISR_Rtr(config)#enable pas

ISR_Rtr(config)#enable password cisco123

ISR_Rtr(config)#li

ISR_Rtr(config)#line vt

ISR_Rtr(config)#line vty 0 4

ISR_Rtr(config-line)#pas

ISR_Rtr(config-line)#password class

ISR_Rtr(config-line)#login

ISR_Rtr(config-line)#exit

ISR_Rtr(config)#lin

ISR_Rtr(config)#line co

ISR_Rtr(config)#line console 0

ISR_Rtr(config-line)#pas

ISR_Rtr(config-line)#password class

ISR_Rtr(config-line)#login

ISR_Rtr(config-line)#exit

ISR_Rtr(config)#

Switch set the all switches

Switch>ena

Switch>enable

Switch#con

Switch#conf

Switch#configure t

Switch#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#host

Switch(config)#hostname Floor1_Sw

Floor1_Sw(config)#ena

Floor1_Sw(config)#enable pas

Floor1_Sw(config)#enable password cisco123

Floor1_Sw(config)#li

Floor1_Sw(config)#line vt

Floor1_Sw(config)#line vty 0 4

Floor1_Sw(config-line)#pas

Floor1_Sw(config-line)#password class

Floor1_Sw(config-line)#login

Floor1_Sw(config-line)#exit

Floor1_Sw(config)#lin

Floor1_Sw(config)#line con

Floor1_Sw(config)#line console 0

Floor1_Sw(config-line)#pas

Floor1_Sw(config-line)#password class

Floor1_Sw(config-line)#login

Floor1_Sw(config-line)#exit

Floor1_Sw(config)#

Do same to switch 2 and switch 3.

Step 3: Configure the interfaces connecting the router and switches

1. Set the interfaces connecting the Floor 1, Floor 2, and Floor 3 switches as trunk ports.
2. Set the interface on the Floor 1 switch connecting to the ISR router as a trunk port.
3. Enable the interface on the ISR router connecting to the Floor 1 switch.
4. Create and configure three sub-interfaces on the ISR routers FastEthernet 0/0 interface. Use the following table.

1.       Set the encapsulation for each sub-interface.

2.       Set the IP address for each sub-interface.

a.        Floor1_Sw(config)#interface gigabitEthernet 1/1

Floor1_Sw(config-if)#sw

Floor1_Sw(config-if)#switchport mo

Floor1_Sw(config-if)#switchport mode tr

Floor1_Sw(config-if)#switchport mode trunk

Do same to switch 2 and switch 3.

b.      Floor1_Sw(config)#interface fastEthernet 0/24

Floor1_Sw(config-if)#sw

Floor1_Sw(config-if)#switchport mo

Floor1_Sw(config-if)#switchport mode tr

Floor1_Sw(config-if)#switchport mode trunk

c.       ISR_Rtr(config)#int

ISR_Rtr(config)#interface f

ISR_Rtr(config)#interface fastEthernet 0/0

ISR_Rtr(config-if)#no ip add

ISR_Rtr(config-if)#no ip address

ISR_Rtr(config-if)#no sh

ISR_Rtr(config-if)#no shutdown

ISR_Rtr(config-subif)#exit

ISR_Rtr(config)#

d.      ISR_Rtr(config)#int

ISR_Rtr(config)#interface f

ISR_Rtr(config)#interface fastEthernet 0/0.20

1.       ISR_Rtr(config-subif)#en

ISR_Rtr(config-subif)#encapsulation dot1q 20

2.       ISR_Rtr(config-subif)#ip ad

ISR_Rtr(config-subif)#ip address 192.168.20.1 255.255.255.0

ISR_Rtr(config-subif)#exit

Step 4: Configure a VTP Domain

Utilize the following table to configure the Floor 1, Floor 2, and Floor 3 switches.

a.       Floor 2 dan 3

1.       Floor2_Sw(config)#vt

Floor2_Sw(config)#vtp do

Floor2_Sw(config)#vtp domain SiteX

Changing VTP domain name from NULL to SiteX

2.       Floor2_Sw(config)#vt

Floor2_Sw(config)#vtp mo

Floor2_Sw(config)#vtp mode cl

Floor2_Sw(config)#vtp mode client

Setting device to VTP CLIENT mode.

3.       Floor2_Sw(config)#vt

Floor2_Sw(config)#vtp pas

Floor2_Sw(config)#vtp password ciscoVTP

Setting device VLAN database password to ciscoVTP

Floor2_Sw(config)#exit

b.      Floor 1

1.       Floor1_Sw(config)#vt

Floor1_Sw(config)#vtp do

Floor1_Sw(config)#vtp domain SiteX

Domain name already set to SiteX.

2.       Floor1_Sw(config)#vt

Floor1_Sw(config)#vtp mo

Floor1_Sw(config)#vtp mode se

Floor1_Sw(config)#vtp mode server

Device mode already VTP SERVER.

3.       Floor1_Sw(config)#vt

Floor1_Sw(config)#vtp pa

Floor1_Sw(config)#vtp password ciscoVTP

Setting device VLAN database password to ciscoVTP

Floor1_Sw(config)#exit

Step 5: Configure VLANs

Utilize the following table to configure the VLANs from the VTP server.

        Floor1_Sw(config)#vl

Floor1_Sw(config)#vlan 20

Floor1_Sw(config-vlan)#na

Floor1_Sw(config-vlan)#name Admin

Floor1_Sw(config-vlan)#exit

Floor1_Sw(config)#vl

Floor1_Sw(config)#vlan 25

Floor1_Sw(config-vlan)#na

Floor1_Sw(config-vlan)#name Management

Floor1_Sw(config-vlan)#exit

Floor1_Sw(config)#vl

Floor1_Sw(config)#vlan 30

Floor1_Sw(config-vlan)#na

Floor1_Sw(config-vlan)#name Finance

Floor1_Sw(config-vlan)#exit

Floor1_Sw(config)#

Step 6: Add switch ports to the appropriate VLAN

1. Configure the Floor 1 switch so that FastEthernet 0/1 is on VLAN 20.
2. Configure the Floor 2 switch so that FastEthernet 0/1 is on VLAN 25.
3. Configure the Floor 3 switch so that FastEthernet 0/1 is on VLAN 30.

a.       Floor1_Sw(config)#int

Floor1_Sw(config)#interface f

Floor1_Sw(config)#interface fastEthernet 0/1

Floor1_Sw(config-if)#sw

Floor1_Sw(config-if)#switchport mo

Floor1_Sw(config-if)#switchport mode ac

Floor1_Sw(config-if)#switchport mode access

Floor1_Sw(config-if)#sw

Floor1_Sw(config-if)#switchport ac

Floor1_Sw(config-if)#switchport access v

Floor1_Sw(config-if)#switchport access vlan 20

Floor1_Sw(config-if)#exit

Floor1_Sw(config)#

b.      Floor2_Sw(config)#int

Floor2_Sw(config)#interface f

Floor2_Sw(config)#interface fastEthernet 0/1

Floor2_Sw(config-if)#sw

Floor2_Sw(config-if)#switchport mo

Floor2_Sw(config-if)#switchport mode ac

Floor2_Sw(config-if)#switchport mode access

Floor2_Sw(config-if)#sw

Floor2_Sw(config-if)#switchport ac

Floor2_Sw(config-if)#switchport access v

Floor2_Sw(config-if)#switchport access vlan 25

Floor2_Sw(config-if)#exit

Floor2_Sw(config)#

c.       Floor3_Sw(config)#int

Floor3_Sw(config)#interface f

Floor3_Sw(config)#interface fastEthernet 0/1

Floor3_Sw(config-if)#sw

Floor3_Sw(config-if)#switchport mo

Floor3_Sw(config-if)#switchport mode ac

Floor3_Sw(config-if)#switchport mode access

Floor3_Sw(config-if)#sw

Floor3_Sw(config-if)#switchport ac

Floor3_Sw(config-if)#switchport access v

Floor3_Sw(config-if)#switchport access vlan 30

Floor3_Sw(config-if)#exit

Floor3_Sw(config)#

Step 7: Connect and configure client workstations

1. Connect PC0 to the Floor 1 switch via FastEthernet 0/1.
2. Connect PC1 to the Floor 2 switch via FastEthernet 0/1.
3. Connect PC2 to the Floor 3 switch via FastEthernet 0/1.

Step 8: Verify connectivity

1. Using the Command Prompt, ping PC1 and PC2 from PC0.
2. Using the Command Prompt, ping PC0 and PC2 from PC1.
3. Using the Command Prompt, ping PC0 and PC1 from PC2.
4. Your completion percentage should be 100%. If not, click Check Results to see which required components are not yet completed.

KONFIGURASI ROUTER STATIS

KONFIGURASI ROUTER STATIS

cara konfigurasi :

konfigurasi router 0
================
Router>en
Router#conf t
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.3.1 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#int se2/0
Router(config-if)#ip add 172.16.2.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#ip route 0.0.0.0 0.0.0.0 ser2/0

konfigurasi router 1
==========
Router>en
Router#conf t
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.1 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#int se2/0
Router(config-if)#ip add 172.16.2.2 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#int se3/0
Router(config-if)#ip add 192.168.1.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#ip route 172.16.3.0 255.255.255.0 ser2/0
Router(config)#ip route 192.168.2.0 255.255.255.0 ser3/0

konfigurasi router 2
============
Router>en
Router#conf t
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#int se2/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#nshutdown
Router(config-if)#exit

Router(config)#ip route 172.16.0.0 255.255.252.0 ser2/0

PC 0
=====
ip address : 172.16.3.2
subnet mask: 255.255.255.0
def.gateway: 172.16.3.1

PC 1
=====
ip address : 172.16.1.2
subnet mask: 255.255.255.0
def.gateway: 172.16.1.1

PC 3
=====
ip address : 192.168.2.2
subnet mask: 255.255.255.0
def.gateway: 192.168.2.1